Temps requis :
About 30 minutes
Beginner
Beginner
Vous venez d’apprendre les habiletés nécessaires pour compléter ce projet, ou vous ne les avez mises en pratique que quelques fois auparavant.

Collier lariat en cuir et perles en bois sarcelle

Ajoutez un peu de rusticité à votre garde-robe à l'aide de ce collier lariat en cuir et perles en bois sarcelle!
Étape 1

Unwind the brown leather from the card.

Étape 2

Measure and cut four 13" [33 cm] pieces from one end.

Étape 3

Make your two tassels by adding two of the leather pieces to a metal frame bead with a lark’s head knot. Set one tassel aside.
TIP: Align two 13" [33 cm] leather pieces and fold in half. Place the fold under the bottom of one metal frame bead. Pull the ends up and around the metal from and pull through the fold of the leather. Pull the ends so the lark’s head knot fits tight against the metal frame bead. Make sure the smooth side of the leather is facing out and the ends are even.

Étape 4

Tie one end of the remaining long leather strip to the top of the metal frame bead on your tassel. Allow about 2"-3" [5.1 cm-7.6 m] of the excess leather on the end after the lark’s head knot is tied.

Étape 5

Add a wood bead from the other end and slide down to sit on top of the lark’s head knot. Thread the short end of the leather through the bead and tie an overhand knot. Cut excess leather piece so it is flush with the knot.
TIP: You may have to ream your wood to make the hole a little bigger to allow for the working leather as well as the small excess leather. You can also add a dab of glue to the leather end trimmed against the knot for an extra secure hold.

Étape 6

For the opposite end, add eight beads in the opposite pattern as the beads on the first end.
TIP: You will tie knots after you have the tassel attached.

Étape 7

Attach the second tassel to the end with a lark’s head knot as you did the first end.

Étape 8

Working back up the leather, slide the last bead added down to sit on top of the lark’s head knot. Tie an overhand knot above the bead.

Étape 9

Add more wood beads from the other end and slide down so they sit on top of the last knot. Tie an overhand knot above the last bead. Cut excess leather piece so it is flush with the knot.
TIP: Again, you may add a dab of glue to the leather end trimmed against the knot for an extra secure hold.

Étape 10

Slide the seven beads down so they are siting on top of the knot and tie an overhand knot above the top bead.

Étape 11

Finally, fold your long leather piece in half, then adjust so the tassels are uneven. Add a larger, round metal bead at the fold with a lark’s head knot to complete your lariat necklace.

Share your project photos with #MakeItWithMichaels

Matériel

Mesures à prendre pour les produits

Mesures à prendre pour les produits

Matériel
 

    Products

  • Ajouter aux options du panier
  • Vous aurez besoin de : 1
    No d’article 10210239 
    13,99$
    Ajouter aux options du panier
  • Vous aurez besoin de : 1
    No d’article 10265341 
    9,99$
    Ajouter aux options du panier
  • Vous aurez besoin de : 1
    No d’article 10508439 
    5,99$
    Ajouter aux options du panier
 
Outils

Mesures à prendre pour les produits

Outils
 

    Produits

  • Vous aurez besoin de : 1
    No d’article 10225204 
    6,99$
    Ajouter aux options du panier
 

Mesures à prendre pour les produits

Vous aurez également besoin de
  • Règle
+ Voir plus