
rainbow loom™ starburst mask headband
Step 1 |
The loom configuration is where the center column (B) positioned one peg off the left (A) and right (C) columns. Connect two looms together so you have one long loom. |
Step 2 |
Working in the direction of the red arrow pointing up (or away), load loom with border bands and push them down to the bottom of the peg:
|
Step 3 |
To load loom for the starburst:
|
Step 4 |
Repeat pattern down the loom for nine starbursts. |
Step 5 |
Take a rubber band and twist to a figure 8 and layer over each starburst center peg and the end peg (pegs B2, B4, B6, B8, B10, B12, B14, B16, B18 and B19). Push down. |
Step 6 |
Turn the loom around so the direction of the red arrow is pointing down (or toward you). |
Step 7 |
Take the hook, go through the peg (B19) and get under the rubber bands. Grab the top band (below the cap band) and move it from B19 to B18. |
Step 8 |
With your hook, reach inside peg B18 and grab the top rubber band and move it to its corresponding peg (from where the bottom half of the band is wrapped). Continue this around the starburst. |
Step 9 |
Repeat the pattern in Step 8 up the loom for each starburst. |
Step 10 |
Go back down to peg B19 and move the border bands forward, up the pegs to secure the bands. |
Step 11 |
Attach a C-clip to the rubber band on B19. |
Step 12 |
Reach into peg B1, grab a new rubber band with your hook. While hold one end of the band, pull the other up through the peg. Place the side you are holding onto the hook. Add a C-clip. |
Step 13 |
Carefully remove the starburst headband from the loom by pulling and rocking it back and forth. TIP: Attach the elastics of your face mask with the C-clips at each end of your Rainbow Loom™ Starburst Mask Headband. Share your project photos with #MakeItWithMichaels |
Step 1 |
The loom configuration is where the center column (B) positioned one peg off the left (A) and right (C) columns. Connect two looms together so you have one long loom. |
Step 2 |
Working in the direction of the red arrow pointing up (or away), load loom with border bands and push them down to the bottom of the peg:
|
Step 3 |
To load loom for the starburst:
|
Step 4 |
Repeat pattern down the loom for nine starbursts. |
Step 5 |
Take a rubber band and twist to a figure 8 and layer over each starburst center peg and the end peg (pegs B2, B4, B6, B8, B10, B12, B14, B16, B18 and B19). Push down. |
Step 6 |
Turn the loom around so the direction of the red arrow is pointing down (or toward you). |
Step 7 |
Take the hook, go through the peg (B19) and get under the rubber bands. Grab the top band (below the cap band) and move it from B19 to B18. |
Step 8 |
With your hook, reach inside peg B18 and grab the top rubber band and move it to its corresponding peg (from where the bottom half of the band is wrapped). Continue this around the starburst. |
Step 9 |
Repeat the pattern in Step 8 up the loom for each starburst. |
Step 10 |
Go back down to peg B19 and move the border bands forward, up the pegs to secure the bands. |
Step 11 |
Attach a C-clip to the rubber band on B19. |
Step 12 |
Reach into peg B1, grab a new rubber band with your hook. While hold one end of the band, pull the other up through the peg. Place the side you are holding onto the hook. Add a C-clip. |
Step 13 |
Carefully remove the starburst headband from the loom by pulling and rocking it back and forth. TIP: Attach the elastics of your face mask with the C-clips at each end of your Rainbow Loom™ Starburst Mask Headband. Share your project photos with #MakeItWithMichaels |